User:Rishabhsuthar32/GSoC20/Report

From BRL-CAD
< User:Rishabhsuthar32
Revision as of 13:43, 29 August 2020 by Rishabhsuthar32 (talk | contribs) (→‎To Do List)

Project Report

Project Plan

BRL-CAD has one of the oldest and fastest parallel ray tracing implementations around but it doesn't currently leverage the GPU very much. With implicit geometry and constructive solid geometry (CSG) Boolean operations, it also has a very different approach to ray tracing that has its own set of academic challenges.

The project here was to introduce a GPGPU pipeline into BRL-CAD using OpenCL for existing primitives and parallelize them for faster computation compared to the non-GPGPU implementation.

Some of the primitives that were planned to be converted in this 2020 season of Google Summer of Code are polyhedron with an arbitrary number (ARBN), FASTGEN4 CLINE, hyperboloids of one sheet (HYP), etc.


Patches Submitted

Following patches include modifications for better functioning and resolution of bugs encountered while rendering via OpenCL in MGED terminal.

Following are the patches submitted for OpenCL versions of some of the primitives.


Performance

We shall take the example of HYP primitive here for comparing the performance of C and OpenCL versions of rendering.

C rendering of HYP
OpenCL rendering of HYP

First Test: Both the C and OpenCL renderings should look same

On the left is the C rendering of the HYP primitive and on the right is its counterpart rendered after enabling OpenCL. Well, on first look, they do look same. First test passed!


Second Test: The performance of the OpenCL version should be much better than the C version

So, let's compare the time displayed in their rendering logs now. While the time taken by the C version to render was 0.31 seconds, the time taken by the OpenCL version to render was 0.02 seconds. That is more than 15x improvement in the performance! Hurray!


pixdiff image of both versions

Third Test: Checking the difference between images at a pixel level

Using the pixdiff and pix-png command of BRL-CAD, a pixdiff image shown on the right was created. The image shows where the colour values differ by more than 1 value in one or more of the RGB channels. Most of the pixels are offset in intensity by just a little bit, which implies some calculation is just slightly off. However, the hits and misses appears to be correct.


Fourth Test: To confirm the hits are identical

On comparing the nirt shotline in both the renderings, the hits were found to be identical, which implies the mismatch in intensity found in above test is a normal issue.


To Do List

  • Memory Allocation : One of the major challenges I faced was finding the OpenCL counterpart of bu_malloc which works fine while passing the variables from .c to .cl file. While I tried with malloc as is used normally in C programs, it apparently didn't work. The renderings were simply not occurring in the OpenCL version. Hence, the HYP and SUPERELL primitives, which didn't use the bu_malloc command, rendered easily while others didn't. The patches submitted above have no compilation or computation error. If the memory allocation thing works, they'd render just as fine.
  • Using Printf statement: Another issue where I got stuck was being unable to use printf statement in OpenCL files. The strategy to debug opencl kernels using printf is to enable printf command by passing enumerations stated below in an array of context properties to the function, clCreateContext, which creates opencl context as follows:

CL_PRINTF_CALLBACK_ARM 0x40B0 CL_PRINTF_BUFFERSIZE_ARM 0x40B1 cl_context_properties context_properties[] = { 

   CL_PRINTF_CALLBACK_ARM, (cl_context_properties)printf_callback,
   CL_PRINTF_BUFFERSIZE_ARM, (cl_context_properties)0x100000,
   CL_CONTEXT_PLATFORM, (cl_context_properties)platform,
   0

};

This enables the device side printf built in function for OpenCL C versions prior to 1.2. It also extends the cl_context_properties enumeration to allow a user defined printf callback and/or printf buffer size. OpenCL kernel code then has access to: 

   #pragma OPENCL EXTENSION cl_arm_printf : enable

This pragma must be enabled for a kernel to have access to the printf built in function in OpenCL C versions prior to 1.2.

For the purpose of debugging in mged I used bu_log instead of printf by passing following array of context properties cl_context_properties context_properties[] = { 

   CL_PRINTF_CALLBACK_ARM, (cl_context_properties)bu_log,
   CL_PRINTF_BUFFERSIZE_ARM, (cl_context_properties)0x100000,
   CL_CONTEXT_PLATFORM, (cl_context_properties)platform,
   0

};

But unfortunately this doesn't work and reports error that context cannot be created. This needs further investigation. The print statement would also be useful for debugging the memory allocation issue, as to where and why it is failing.

References

Retrieved from "https://brlcad.org/w/index.php?title=User:Rishabhsuthar32/GSoC20/Report&oldid=11787"